How To Set Up Beer Keg
This is a general reference guide for assembling and installing a standard full-size kegerator. Depending on the kegerator brand, make, and model, slight modifications may be needed in the assembly and installation. Please be sure to refer to the user manual that comes with your specific model.
For a visual reference of parts that are numbered in parentheses in this installation guide, please view the kegerator diagram below.
Listed Parts:
- Faucet Handle
- Faucet
- Beer Tower
- Guard Rail
- Baste Tray
- Regulator
- CO2 Tube
- CO2 Cylinder
- CO2 Holder
- Keg Coupler
- Metal Keg Floor Support
- Pulley Washer (x2)
- Casters (x4)
- Neoprene Washer
- Snap-On Clamps (x2)
- Wire Shelves (not pictured) (x2)
- Half Barrel Keg (non included)
- Faucet Wrench (not pictured)
For a more in-depth review of what each component is, please refer to our Kegerator Parts commodity.
Pace-by-Step Instructions for Assembling Your Kegerator
Follow these pace-by-step instructions for assembling your kegerator and installing/tapping a keg within of information technology.
1. Install Caster Wheels
Earlier starting time, make certain the unit is empty – including the white metal keg floor (11). And then, carefully tip the beer dispenser on its side. Connect the casters (thirteen) to the cabinet by screwing in each metal bracket into ane of four pulley holes. The casters in the front of the chiffonier require the washers (12). When done, advisedly prepare the unit upright.
2. Remove Plug
Open up the door, and with your mitt push the peak cabinet plug through the meridian of the cabinet until it comes out. Alternately, you tin can use a flat head screwdriver every bit a prying tool.
3. Install Tower
Now you can begin to install the typhoon tower (3). Unravel the beer line hose from the bottom of the belfry, and feed the hex nut and beer line through the hole you uncovered in the top of the chiffonier.
4. Secure Tower
In one case you have fed all the line into the chiffonier, you are ready to place the tower into the unit. Marshal the black plastic adapter on the bottom of the belfry to the pigsty in the tiptop of the cabinet. Once the adapter is securely lined up to the hole, turn the adapter almost 25° clockwise to lock information technology into place. The faucet connection for the tower should now face up the forepart of the chiffonier, only if not remove information technology and reinstall from another position.
5. Install Railing
Take the railing (4) and identify information technology's feet into the pilot holes in the summit of the cabinet.
half-dozen. Install Handle Faucet
Screw the black faucet handle (1) on to the faucet (2), then screw the faucet onto the faucet adapter on the front end of the tower (3). Make sure the faucet is vertical with the blackness handle facing the ceiling, and the faucet should exist screwed on tightly. Place the plastic baste tray (5) beneath the faucet.
6. Connect Tube to Regulator
Check the switch below the main body to make sure the CO2 regulator (6) close off valve is airtight (the switch should be perpendicular to the tubing). Install the 4 ft. CO2 gas line tube (7) to the regulator by attaching i terminate of the tube into the hose barb connexion on the CO2 regulator and secure the tube past using one of the two cocky-locking cherry plastic snap-on clamps (15). Use pliers or clamp crimpers to snap the clamp on as high every bit possible, and make sure the clamp does not impede the valve. Then remove the black rubber plug from the back of the unit and feed the remaining unused end of the tubing through the hole.
seven. Connect Regulator to Cylinder
Make sure the CO2 cylinder (eight) is full and closed. Then attach the CO2 regulator (half dozen) to the cylinder past screwing the loose golden regulator nut into the cylinder valve and tightening with a wrench or pliers. Note that a fiber washer is normally required to connect a regulator to a CO2 cylinder, only a standard regulator generally includes a built-in O-ring.
8. Mount CO2 Cylinder
Now mount the CO2 cylinder holder (ix) to the chiffonier. Match up the holes on the holder with the screws bulging out of the dorsum of the cabinet and slide the holder downwards to lock it in place. Position the CO2 regulator (6) in the holder so that you volition be able to read the numbers on the guess and have easy access to the close-off valve.
ix. Connect Keg Coupler
To connect the keg coupler (x) to the keg (17), first make sure the black pull handle of the keg coupler is in the airtight (diagonal/upper) position. Insert the keg coupler into the locking cervix of the beer keg and turn clockwise 25° to lock in into place. Now the keg coupler is secured to the keg.
10. Attach Tube to Coupler
At present attach the remaining open end of the CO2 gas line tube (7) to the keg coupler'south hose barb (10). Then secure the tube past using the remaining self-locking ruddy plastic snap-on clench (15). Use pliers or clench crimpers to snap the clamp securely equally close to the coupler as possible.
11. Connect Beer Line to Coupler
Now connect the beer line from the tower (three) to the keg coupler. Insert the neoprene washer (xiv) into the beer line hex nut (the beer line is the line coming from the tower and faucet). Remove the blueish safety protective cap located on tiptop of the keg coupler and firmly screw the nut with the neoprene washer to the top of the keg coupler.
12. Tap Keg
To secure the tank connectedness, pull the tap handle out — away from the keg coupler (10) — and push button down until it locks into position. Listen for the "click" of the pull handle when information technology shifts into the final downward position, and your keg volition exist tapped.
xiii. Calibrate Regulator
Below are footstep-by-pace instructions on how to calibrate your regulator. On the right, you lot can see photos to illustrate the steps listed.
A:
With the close-off valve on the regulator (6) closed, open the valve on the gas cylinder (eight) completely.
B:
Loosen the aligning nut with a pair of pliers, allowing the adjustment screw to be turned counter-clockwise until the screw can no longer turn.
C:
Slowly turn the regulator adjustment screw until the desired pressure level is shown on the output pressure gauge. Under normal circumstances, we recommend setting the regulator at 12 PSI.
Notation: Other conditions, such as altitude or special beer blazon, may crave some adjustment. On regulators designed for typhoon beer, turning clockwise will increment the output pressure, and turning counter-clockwise volition decrease the output pressure.
D:
Open the shut-off valve on the regulator, ensuring the switch below the main body should be parallel to the tubing. Gas should now menstruum from the regulator to the keg coupler (10), and you will hear the keg pressurizing. The output needle will drop momentarily while the pressure level is equalizing, and then it will return to the point at which you set it.
E:
The keg coupler is designed with a pressure level relief valve (PRV). Pull the ring on the PRV briefly to allow gas to vent. This will permit gas to flow through the regulator and help obtain a more accurate reading on the output pressure level gauge.
F:
Re-bank check the output pressure level on the regulator and, if necessary, re-adjust using step B until the desired pressure is shown.
Note: It is ever wise to follow upward any adjustment to the regulator with a brief pull of the PRV ring to ensure an accurate output reading.
14. Position Keg & Enjoy!
Place the metallic keg floor support (11) back into the cabinet. And then, advisedly tilt the beer keg (17) and residue the border on the keg floor support on the bottom of the interior cabinet. Slide the keg in slowly, ensuring that it is properly located, and all hoses are clear of obstructions. Shut door and enjoy some refreshing draft beer!
That's It!
Now that your keg is fully assembled and the keg is tapped, the just thing left to practice is savour a fresh draft beer right in the comfort of your habitation. If you lot have any questions well-nigh assembling or installing your keg, delight exit them in the comments below or give us a call at one-866-950-8710.
How To Set Up Beer Keg,
Source: https://learn.kegerator.com/assembly-guide/
Posted by: leewithis.blogspot.com
0 Response to "How To Set Up Beer Keg"
Post a Comment